How to Replace- iPhone XR back Glass

The user wants a step-by-step guide, so I need to look through the search results provided and find the most relevant information.

First, I notice that there are multiple methods mentioned. The Noor Telecom guide (webpage 1) goes into a detailed teardown, which involves removing the screen and internal components.

But then there are other methods, like using a laser separator (webpages 3 and 6) which seems to be a more advanced technique but might preserve the original thickness better. Also, some YouTube videos are listed, but their content isn’t accessible here.

Webpage 3 and 6 both talk about using a laser machine to soften the adhesive, making the glass easier to remove. That’s interesting because it might be a less invasive method compared to full disassembly.

However, the laser machine is expensive and probably not available to most DIYers. The user might not have access to that, so alternative methods using heat guns or hair dryers are also important.

Webpage 8 discusses the heat and pry tool method, which is more accessible. It mentions the steps of heating the edges, using a suction cup, and prying the glass off.

This seems like a common approach. Also, webpage 9 has detailed steps about removing screws, using a suction cup, and cleaning adhesive residue.

I need to combine these methods. The answer should probably outline the main approaches: the full disassembly method from NoorTelecom, the heat and pry method, and the laser method.

But since the user is asking for a DIY guide, the heat and pry method is more feasible. However, the NoorTelecom guide requires taking apart the phone, which is more involved.

Wait, the user is asking specifically for the back glass replacement. The NoorTelecom guide in webpage 1 is about rear glass replacement but involves disassembling the phone, removing the battery, display, etc.

Whereas webpage 3 and 6 suggest that using a laser avoids disassembly. But since the laser is not accessible, the alternative is using heat and prying. However, some sources mention that removing the back glass without disassembling the phone can risk damaging internal components.

So maybe there are two main methods: one with full disassembly (more thorough but complex) and one without (riskier but quicker). The answer should present both options, highlighting the pros and cons.

Also, webpage 9 gives a detailed step-by-step for replacing the back cover, including removing screws, using a suction cup, disconnecting the battery, cleaning adhesive, etc. It seems comprehensive.

I need to structure the answer by first listing the tools needed, then the steps for each method. The answer should mention that the laser method is professional,

while the heat and pry is DIY. Also, note the importance of preserving the original adhesive to maintain thickness.

Potential steps would be:

1. Preparation and tools
2. Heating the adhesive
3. Removing the broken glass
4. Cleaning the area
5. Applying new adhesive
6. Installing new glass
7. Reassembly and testing

But also, if using the disassembly method, steps like removing the screen, disconnecting the battery, etc., are necessary .

I should mention the importance of being careful with the battery and internal components, as breaking them can cause further issues. Also, using isopropyl alcohol for cleaning (webpages 3,6,8,9) and proper adhesive application.

The answer should include warnings about the risks, maybe recommend professional help if unsure, and note that Apple’s repair program might be an option.

Now, putting this all together into a coherent guide, citing the relevant sources where each step is mentioned. Make sure to differentiate between methods where possible and highlight the key considerations.

Replacing the back glass on an iPhone XR requires precision and careful handling to avoid damaging internal components. Below is a detailed guide synthesizing methods from the search results, categorized by complexity and accessibility:

Method 1: Heat and Pry Tool Method (DIY-Friendly)
Tools Needed:
Heat gun/hair dryer
Suction cup and plastic pry tools
Precision screwdrivers (Y000 and Phillips #000)
Replacement back glass and adhesive strips
Isopropyl alcohol and cleaning cloth

Steps:
Power Off: Ensure the iPhone is turned off to prevent short circuits.
Remove Bottom Screws: Use a pentagonal screwdriver to remove the two screws at the bottom edge.

Heat the Edges: Apply heat evenly around the edges of the back glass for 1–2 minutes to soften the adhesive (1011).
Create a Gap: Attach a suction cup near the bottom edge, pull gently, and insert a plastic pry tool to separate the glass.

Remove Glass: Slowly work the pry tool around the perimeter, lifting the glass while reheating stubborn areas. Avoid prying near the camera or wireless charging coil.

Clean Residue: Use isopropyl alcohol to remove old adhesive and glass debris. Preserve existing adhesive if possible to maintain original thickness.
Apply New Adhesive: Align and press the new back glass onto the frame, using clamps to secure it for 10–15 minutes

Reassemble: Reconnect components (if disassembled) and tighten screws.

Method 2: Full Disassembly (Advanced)
Tools Needed:
Anti-Clamp or suction handle
Magnetic project mat and spudger
Laser separator (optional for professionals)

Steps:
Remove Screen: Follow NoorTelecom’s teardown guide to disconnect the battery, display, and logic board
Battery Removal: Pull battery adhesive tabs or use dental floss to slice adhesive.
Internal Component Access: Remove screws securing the logic board, camera plate, and grounding bracket .

Replace Glass: After full disassembly, replace the back glass and reassemble in reverse order .
Method 3: Laser Machine (Professional)
Process: A laser separator melts adhesive without damaging internal components.

This method preserves the original thickness by retaining existing adhesive layers .
Drawbacks: Requires expensive equipment (~$2,000) and expertise, making it impractical for most DIYers.

Key Considerations:
Adhesive Preservation: Retaining the original adhesive or reapplying it precisely ensures the iPhone’s thickness matches the factory design.

Risks:
Damaging the battery, wireless charging coil, or camera during prying.
Voiding warranty if using non-Apple parts .

Alternatives:
Back Housing Swap: Replace the entire frame/glass assembly for a like-new finish.
Final Tips:
Test functionality (e.g., wireless charging, camera) after reassembly.
Use clamps to ensure adhesive bonds properly.

If unsure, seek professional help to avoid irreversible damage.

For visual guides, refer to NoorTelecom’s tutorials or Forward Tools’ laser method
This is a laser Machine. Set your phone set facing the back glass.

Now, command from the software and choose from the dropdown list- iPhone XR, and it will appear will iPhone XR graph also. Now, look at the laser machine it is working. Set it properly and in the correct position. you can see it Laser machine Damaging the back glass part by part.
Laser machine work is done. Now, Choose this type of tool as you see. Remove the glass carefully cause it can hurt you. before, fixing the back glass and cleaning it properly. To fit the back glass need to put some glue.

The back glass can be pressed with something to fit properly or can be tied with something. Or you can use the tools you see in the video.